Linear Technology LTC3614 synchronous buck regulator
22 April, 2010 | element14
The LTC3614 is a high-efficiency synchronous buck regulator from Linear Technology that incorporates a constant frequency, current mode architecture capable of switching frequencies up to 4 MHz.
B&K Precision XLN series of DC power supplies
22 April, 2010 | Unispan Instruments Pty Ltd
The B&K Precision XLN series of DC power supplies provides up to 1440 W of power in a 1U, full-rack case for rack mounting in an ATE environment or for benchtop use.
B&K Precision models 4076 and 4079 50 MHz arbitrary waveform/function generators
22 April, 2010 | Unispan Instruments Pty Ltd
B&K Precision has announced two 50 MHz arbitrary waveform/function generators, models 4076 and 4079, that allow design of a required signal by using the generator’s function or arbitrary waveform section.
Advantech NCP-7560 Packetarium network platform
22 April, 2010 | Advantech Australia Pty Ltd
Advantech’s Network and Telecom Group has released its high-end Packetarium platforms for wire-speed packet processing. The NCP-7560 is a 4U rackmount network appliance, scalable from 12 to 96 cores based on the Cavium Networks Octeon Plus network processor.
ICP Electronics ISC-4110U/8110U industrial media converter series
22 April, 2010 | ICP Electronics Australia
ICP Electronics has launched the ISC-4110U/8110U industrial media converter series. The 4110U offers USB to 4x RS232 serial ports, while the 8110U features USB to 8x RS232 serial ports.
Mornsun URA_LD-20 W DC/DC converter
22 April, 2010 | DLPC Pty Ltd
Mornsun has launched a 4:1 wide input, dual output 20 W isolation DC/DC converter URA_LD-20 W which meets EMI standards.
Siemens Simatic CPU 317TF-2DP controller
22 April, 2010 | Siemens Ltd
The Simatic CPU 317TF-2DP controller enables motion control, safety and standard tasks in one device. It uses PLCopen-compatible motion control blocks. It is suitable for applications from controlled single-axis positioning to complex, synchronised sequences of motion, eg, geared synchronous motion, curve synchronisation or print mark correction.
MEN CT12 3U CompactPCI transition module
22 April, 2010 | Dominion Electronics
The CT12 is a 3U CompactPCI transition module for use in combination with MEN’s PICMG 2.30-based single board computers.
Dominion Electronics G501 CompactPCI serial hard drive carrier board
22 April, 2010 | Dominion Electronics
The G501 is a CompactPCI serial hard disk drive carrier board, designed to carry a 2.5″ SATA hard disk drive (RAID level depending on the CPU) or a solid-state drive.
Moxa IMC-P101 series industrial PoE media converters
22 April, 2010 | CrispTech Pty Ltd
Moxa has announced the IMC-P101 series UL508-certified industrial PoE media converters that provide IEEE 802.3af PoE ethernet-to-fibre media conversion from 10/100BaseT(X) to 100BaseFX(SC/ST) in a -40 to 75°C operating temperature range in harsh environments.
FiberSensing FS 6500 FBG accelerometer
22 April, 2010 | Bestech Australia Pty Ltd
Bestech Australia has released the FS 6500 FBG accelerometer from FiberSensing.
ICP Electronics PM-PV-D510/N450 PC/104 low-power SBCs
22 April, 2010 | ICP Electronics Australia
ICP Electronics has released the PM-PV-D510/N450 PC/104 low-power SBCs based on the Intel Atom D510 and N450 processors.
Farnell LTC3521 buck-boost with step-down DC/DC converters
22 April, 2010 | element14
The LTC3521 combines a synchronous 1A buck-boost DC/DC converter with dual 600 mA synchronous step-down DC/DC converters to offer three output rails with efficiencies as high as 95%. Its input range of 1.8 to 5.5 V makes it compatible with all types of PC card slots, USB and single-cell Li-Ion or dual/triple-cell alkaline/NiCd/NiMH applications.
EM Test ESD 30N ESD tester
22 April, 2010 | Consultant Technology Australia Pty Ltd
The EM Test ESD 30N is an ESD tester for simulating ESD pulses to 30 kV with discharges up to 20 Hz in both air and contact discharge modes.
PMM 9010/9030P EMI test receiver
22 April, 2010 | Consultant Technology Australia Pty Ltd
The PMM 9010/9030P EMI test receiver has two RF inputs, one covering compliant EMC RF emission testing between 9 kHz and 30 MHz (conducted emissions) and the other for precompliant (radiated) testing between 30 MHz and 3 GHZ.
